What’s up guys, I’m Brad Rodriguez from Fix This Build That and today I’m gonna show you how to make this DIY base cabinet. It is awesome storage for the garage or workshop. It has drawers as well as doors that have pullout trays in them you can configure it however you want it as many Drawers as you’d like. I’ll show you exactly how I did it stay tuned. I started off the project by breaking down two plywood sheets into smaller sizes for easier handling. I just got the Accu-cut track from Kreg Tool, the sponsor of today’s video, and it’s an awesome pairing with my cordless circular saw. The non-slip track lets me just put it down on the plywood make my cut and move on quickly no cords, no clamping, no problem. I took the sheets to my table saw and I followed my cut list to cut the sides to size and rough out most of the other pieces. I cut the parts to a known width and I’ll size them later to length to fit the build as I make it. I have plans available for this build that include a full cut list to help you minimize waste during cutting and layout you can check the link in the description for more details. The sides are connected with horizontal supports on the top and the bottom. To get all the pieces the same length. I clamp them together and I can cut them over on the miter saw. The toe kick plate is an inch and a half longer than the supports, and I cut it to size as well. Speaking of the toe kick I cut notches on the bottom of each side to accept the kick plate. I used the jigsaw to cut the recess out. Just try to keep it straight of a line as you can on the sides of the kick plate will reference. All the horizontal supports will be attached to the sides using pocket screws. So I drilled two pocket holes on the end of each piece. I highly recommend using the dust attachment for the K4 and K5 jig as it captures the chips coming out and almost eliminates cleanup time. To attach the supports, I laid one side down on the floor and began attaching the pieces vertically. After I have the top and lower back support in place I turned the pieces upright and attach the other side. Because I’ll have drawers or pull outs all across the cabinet I didn’t use a solid bottom panel. The lower horizontal supports are screwed into another support piece turn on edge which will carry the weight of the cabinet. Now this setup shores up the lower supports and gives a place to attach the center dividers, which will be added later. I worked my way around the cabinet flipping and moving it and attached all the lower supports as well as the toe kick plate, which is actually a structural piece. With the frame of the cabinet established I moved on to cutting the pullout trays which will be on both ends of the cabinet. I set up the stop track on my miter saw stand and cut all the pieces to size for the four pull out trays. Next I cut the cabinet dividers to size on the table saw from the sheets that I had cut the width earlier. Each divider is attached to the upper and lower horizontal supports with pocket screws and gets pocket holes on all four corners. To position the cabinet dividers, I use the pullout drawer fronts in the drawer slides as spacers to get the exact placement. I attach the dividers with screws, and then I measured for the center drawer widths. Cutting the drawers now vs. at the beginning of the project is a good idea because at this point the width of the drawers is going to be bound by the dividers. With the varying thicknesses of plywood and the possible error in measurements you could easily have a bad fit if you cut the pieces in advance. With all the pullout tray and drawer parts cut to size I took them to the table saw and I cut grooves for the bottom panel. I used a similar method as I do with most of my drawers. First cutting a full kerf eighth of an inch groove a quarter inch up from the bottom then moving the fence over and making another pass to size the groove to my quarter-inch plywood. I raised the blade and I cut the bottom of the back pieces off so that I can slide the panel in after assembly. You’ll see that later. The pullout trays go together really easily, I just squared them up and used glue and Brad nails to join them. I assemble them upside down to make sure that all the grooves are aligned and even with that underside of the back piece. Since the drawers will have false drawer fronts I use pocket holes on the front and back pieces for joinery. A pair clamps here holding the drawers tight makes assembly a breeze. All the trays and drawers get a quarter inch bottom panel. I cut the panels to size and then I slid them into the grooves I cut earlier. Each panel then gets screwed into the back of the drawer with some panhead screws. It gives you a nice solid drawer that is quick to build. Before installing the drawers I went back and attached some mounting cleats to the corners of the cabinet back to shore it up from racking and give an attachment point for the wall. Each side of the cabinet will get two pull out trays one on the bottom and one near the middle. I shimmed up the bottom slides with quarter inch plywood and gave them an eighth of an inch setback. Then I use pilot holes and screws to secure each slide to the cabinet. I use the plywood spacers to support the tray and then it pulled out the slide arms and secured them to the sides. After attaching a front and center screw, I remove the tray and installed a third screw in the back. To secure the middle slides I use the Kreg drawer slide jig. I mark where I wanted the bottom of the slide and the tray to go and then I clamp the jig to the side of the cabinet. The jig gives a large surface for the slide to rest on while you attach the screws. But the real beauty of the jig here is that when you reverse it it acts as a support to hold the tray while you attach the slide arms to the sides. I really like the jig for this application. I mount the slides for the drawers in the middle bay by using similar methods as the trays. Then I did the same thing for the far end of the cabinet to finish off installing the drawers. Since the cabinet’s gonna be in my garage, I wanted to be off the ground. I need adjustable feet so I can level it for the sloped floor. I cut mounting blocks to size and I attach them with glue and Brad nails to the front and back supports on the bottom. I drilled a 7/16 of an inch hole in the bottom of the two pieces to accept some hardware. I’m just gonna use three-eighths of an inch T-nut and carriage bolts here for the levelers. This is a trick I picked up from Jay Bates, which he used over on his miter saw station. While the cabinet was on its back I cut the doors on the drawer fronts to size. This makes it really easy to layout the doors. You can just take some measurements cut the drawer fronts to exactly the size you need them. I used an eighth of an inch spacer to establish the reveal between each drawer here. I’m using concealed hinges to mount the doors to the cabinet now Kreg has another jig for this and it might be my favorite one. You line up the jig on the cabinet door and then you attach the drill to the included forstner bit and drill out the hole for the cup. The coolest part is the depth stop on the bit so you can’t drill it too deep. And now you can just remove the whole piece and then drill the pilot holes for the hinge screws using that same jig. It gave me perfectly aligned holes for mounting the hinges and honestly, It was just kind of fun to use. I attach the hinges to the inside of the cabinet, and then I realized something was no bueno. Okay, guys. I messed up pretty big here, so I made sure that the drawers would not hit the hinges But I did not make sure that the slides would not hit the door. So you see here that this is not going to work. Do not make that mistake if you’re using 110 degree doors. Make sure that you shim out the drawers and make your drawers a little bit smaller To fix this little mess up I went back and installed a quarter inch shim on the outer sides of the cabinets. In retrospect I’d recommend using two layers of the quarter inch or a half inch shim because my fit was still really tight. And yes this meant I had to remake all the trays. Ugh I attached the false drawer fronts to the drawer by drilling quarter-inch through holes and using pocket screws from inside. After that I mounted the pulls to the drawer fronts and doors. I spaced the handles near the top of the drawers for easier access for those lower drawers. I want to replace these handles later on with some shop built ones out of maple, but these are gonna look nice for now. The final piece of the cabinet is the top. I made everything to this point out of just two sheets of plywood. I used a portion of a third sheet for my top, but you could make a solid wood one or use an off-the-shelf countertop as well. To give the top a beefier feel I trimmed it with an inch and a half thick piece of maple hardwood. I used glue and pocket screws on the underside of the top to attach the trim to the front. I left the front piece long to cut to size after the side trim is on. I mounted spacer strips on the underside of the top to raise it off the base and give a spot to attach the screws from underneath. I just attached it with glue and inch-and-a-quarter screws. I flipped the top over and cut the front trim flush with the sides using my flush cut saw. Then I took the top out to the driveway rounded over the edges with my router and sanded everything to 180 grit. I applied two coats of water-based poly to the cabinet and three coats to the top before taking it back inside. I removed the upper pullout trays and secured the top of the cabinet with screws from below. And I was all finished now. This cabinets gonna be an awesome addition to my mid and long term storage in the shop and the possibilities are just really endless with this design. You can size it and number the drawer and door combination to fit your needs I wanna give a big THANK YOU to Kreg Tool for helping me out with this project. Their jigs made this project go a lot faster, and the pocket hole joinery makes the case go together super quick. There’s links down below in the description to all the different items that I use today you can go check them out. If you want plants build your own base cabinet, there’s a link down below in the description. It’ll take you to my plans, and they have 3D diagrams cut lists as well as step-by-step instructions. I want to give a big shout out to all my patrons over there and the Builders Club. Thank you guys for supporting me! If you’re not subscribed in the channel I’d love to have you as part of the channel. And until next time guys get out there and build something awesome!

How to Build a Base Cabinet with Drawers | DIY Shop Storage

100 thoughts on “How to Build a Base Cabinet with Drawers | DIY Shop Storage

  • September 26, 2017 at 4:10 am
    Permalink

    If you want plans to build this base cabinet you can get them here: https://gum.co/basecabinet

    Reply
  • June 8, 2018 at 12:21 am
    Permalink

    I bought the plans and plan to modify to make a longer, deeper cabinet given that I have more space under the table saw. A little disappointed the plans are a pdf. Do you offer the SketchUp plans? That would make modifying the sizes a lot easier!

    Reply
  • June 15, 2018 at 6:17 am
    Permalink

    What are the dimensions for this cabinet? I am remodeling my kitchen and a couple of these would be perfect for it.

    Reply
  • June 22, 2018 at 12:26 am
    Permalink

    My dad gets scared every time I watch these videos because last time a came home and set up saw horses in the living room of our tiny apartment……… I'ma go borrow my friends table saw and set it up next to the tv for when he gets home =)

    Reply
  • June 24, 2018 at 9:30 pm
    Permalink

    great video very informative loved it!

    Reply
  • June 27, 2018 at 12:40 pm
    Permalink

    I like that you made a mistake (at 7:03) because most of my projects I almost ALWAYS mess up something to the point I rarely enjoy it. I made a ghostbusters play table (video on my profile) but I didn't take into account that my sons bedroom door is 1cm smaller than the doors downstairs so on christmas day I was removing the door frame to get it in!) theres always some unforeseen thing that sets me back hours of my time. Not that I like that this happened to you, but it shows that it can even happen to a professional who can make such awesome cabinets.
    When it comes to diy now i usually add at least a day more time to complete due to losing pencils, screwdrivers, something breaking, measuring something wrong, something always messes up no matter how much I plan it but it's nice to see that it was worth pushing through the error to get to the finish piece. excellent

    Reply
  • July 2, 2018 at 7:01 am
    Permalink

    Can I buy this plan showing the cut list in mm in stead of inches

    Reply
  • July 9, 2018 at 11:33 am
    Permalink

    Impressive stuff

    Reply
  • July 19, 2018 at 4:57 pm
    Permalink

    Solid build! I like how you went into really fine details about how you made it!

    Reply
  • July 26, 2018 at 9:06 am
    Permalink

    As much as I have learned from this video, I find you talk way way to quickly as the editing changes …. why such a Rush ?? The video has good lighting and it is informative. Slow down while talking. People take time out of their busy days to click on your videos. Show them that you appreciate them for stopping by and relax your speech. We are trying to associate and relate things together.

    Reply
  • July 26, 2018 at 8:56 pm
    Permalink

    Hi thanks for the helpful video. I need a custom single flatbed drawer that would be used for keeping tools while working at my workshop. But the problem I am having is I don’t have any side support where I can mount the slides. Only option I have is to mount the slide just underneath of the main cabinet and use the top side of flatbed to mount against the drawer. Weight on the flatbed drawer could be upto 25-30kg. Can the flatbed handle this weight when top-mounted like this? Thanks

    Reply
  • July 28, 2018 at 2:22 am
    Permalink

    Good work.

    Reply
  • August 7, 2018 at 3:20 pm
    Permalink

    That's great, looks like a good project for someone with basic tools

    Reply
  • August 16, 2018 at 3:49 pm
    Permalink

    The general knowledge of building cabinets in this video is great! Thank you.

    Reply
  • August 18, 2018 at 3:34 am
    Permalink

    I've rewatched your videos & learn something each time. Thanx for sharing your skills.

    Reply
  • August 18, 2018 at 10:22 am
    Permalink

    Excellent video. Thanks a lot for sharing!

    Reply
  • August 20, 2018 at 6:50 pm
    Permalink

    Nice build man, shame about the slip-up… & thanks for calling it out … I like that..😎
    Regarding your tools list… what mitre saw, make & model u using ? I may be in the market soon..😏

    Reply
  • August 23, 2018 at 4:30 am
    Permalink

    What kind of plywood is this? Any recommendations on plywood not many options of places to shop.

    Reply
  • August 24, 2018 at 3:02 pm
    Permalink

    WOW!!! No dusk mask. Ur strong man! 😀

    Reply
  • August 24, 2018 at 9:33 pm
    Permalink

    Love your table saw. What brand is it?

    Reply
  • August 26, 2018 at 5:34 am
    Permalink

    Hi, what did you have for breakfast? "eeerrrrmmmm, pocket holes..!? How about dinner?" errrrmmmm, pocket holes..!? How about last year? "Errrmmmm……..oh yeah, pocket holes!!!!"

    Reply
  • August 28, 2018 at 10:08 pm
    Permalink

    So bad ass! Love this, thanks for sharing

    Reply
  • September 5, 2018 at 2:20 am
    Permalink

    Can u tell me what plywood u used. Looks like 13 ply or something. Baltic Birch 5×5 but the sheet looked 4×8.

    Reply
  • September 15, 2018 at 9:58 am
    Permalink

    I am from Algeria and your work is great and worth pursuing

    Reply
  • September 27, 2018 at 7:51 pm
    Permalink

    Now that's a very nice tutorial ! Must have been a lot of work… Congratulations for the final result.

    Reply
  • September 28, 2018 at 9:23 am
    Permalink

    Hi there. Great video! About the drawer problem.. how come you didn't just change the hinges to the 180º type? Once the door is open it gets out of the way as it pivots to one side, so I think it would have been easier that for you to redo all the drawers. Just a thought.. Anyway, this is a great project. 🙂

    Reply
  • September 28, 2018 at 4:39 pm
    Permalink

    Everything we need, and nothing we don't. Thank you!
    It's helpful that you included your mistake and the solution including the fact that you would improve your solution in future!
    I keep coming back to your video; it's the most helpful for my needs by far even though I'm only making a single cabinet with floor slides for my trash can drawer.

    Reply
  • October 6, 2018 at 12:29 pm
    Permalink

    Good video! I appreciate it when you guys admit (and often show) publicly your mistakes and how you fixed the problem—it makes me feel better since I invariably ‘screw up’ on a lot of my projects. 😖

    Reply
  • October 9, 2018 at 10:47 pm
    Permalink

    I just want to know why do people want to be sponsored?

    Reply
  • October 11, 2018 at 3:51 pm
    Permalink

    Very beautiful

    Reply
  • October 14, 2018 at 8:07 am
    Permalink

    nice video very informative. i also want make some diy cabinet, minus the tools

    Reply
  • October 19, 2018 at 4:47 pm
    Permalink

    really good done >> good hand >>> good guy

    Reply
  • October 19, 2018 at 5:44 pm
    Permalink

    thank you for all your beautiful work

    Reply
  • October 21, 2018 at 10:38 pm
    Permalink

    This is just what I need!!! Thanks.

    Reply
  • October 23, 2018 at 6:25 pm
    Permalink

    Great job…

    Reply
  • November 2, 2018 at 12:45 pm
    Permalink

    We got the accucut straight edge but couldn’t get it to mount to our ridgid cordless saw because of the clamp on the saw. How did you get yours to mount??

    Reply
  • November 4, 2018 at 12:54 pm
    Permalink

    wow! That cabinet looks amazing. How did you first learn to build a cabinet like that?

    Reply
  • November 9, 2018 at 12:31 am
    Permalink

    great work

    Reply
  • November 10, 2018 at 3:01 am
    Permalink

    What kind of orange hose do you have on the kreg pocket hole jig?

    Reply
  • November 11, 2018 at 1:38 am
    Permalink

    Go VOLS!

    Reply
  • November 21, 2018 at 6:23 am
    Permalink

    Here again this is the push to sell Kreg tools and in no way does the Industrial use this method. Sure you can do it this way but believe me there are obstacles in this effort that clearly are not shown or mention.

    Reply
  • December 2, 2018 at 2:20 am
    Permalink

    i am so sick of kreg and there jigs , they cost way to much , glad i made all those jigs by hand and one goes just make new i hate kreg

    Reply
  • December 2, 2018 at 3:24 am
    Permalink

    Very nice brother thanks

    Reply
  • December 9, 2018 at 12:04 pm
    Permalink

    Step 1: buy $5000 worth of tools….

    Reply
  • December 10, 2018 at 11:21 pm
    Permalink

    BUEN TRABAJO

    Reply
  • December 12, 2018 at 3:17 pm
    Permalink

    That is a nice project. Well Done!!!!!!!

    Reply
  • December 12, 2018 at 10:40 pm
    Permalink

    Seems like a Kreg advertisement

    Reply
  • December 15, 2018 at 2:33 pm
    Permalink

    oh 1:52 is not flash 🙁 I always do that 😀

    Reply
  • December 16, 2018 at 2:51 pm
    Permalink

    Great info and well made video. You look like Flip Rodriquez

    Reply
  • December 17, 2018 at 6:10 am
    Permalink

    The cost to build is higher than buying a mid grade tool cabinet, you also have to spend 1-2 days of your life on it. The only benefit you get is the pleasure of building something, as long as results are ok.

    Reply
  • December 17, 2018 at 6:30 am
    Permalink

    How do I do this? How many cartons do you need and what tools (I am Vietnamese) need to watch your videos?

    Reply
  • December 19, 2018 at 7:59 am
    Permalink

    Great video, I must be a newb because I'm still at the point of asking what kind of plywood did you use and where do you get it? How does it compare to the "Cabinet" grade type from the big box stores?

    Reply
  • December 19, 2018 at 9:31 am
    Permalink

    Love the video! These frameless cabinets are almost the exact kind I was going to build for my kitchen. However, only using braces for the frame and not putting a bottom shelf was something I didn't think of. I've been trying to figure out ways to save wood and that was a good idea thank you. I'm not sure if it'll work, I'm thinking about trying it on my drawers, but another thing you can think about doing instead of having to shim up your drawer rails is to Mount them to the bottom of the drawers instead of the sides. It would require installing a couple of small braces to attach the rails to and will also require using a thicker bottom to the drawer so essentially a little bit more material but on the other hand your drawers could go edge-to-edge and your rails would be hidden on the bottom.

    Reply
  • December 25, 2018 at 5:04 am
    Permalink

    very nice.

    Reply
  • December 26, 2018 at 1:53 am
    Permalink

    Nice video thanks

    Reply
  • December 26, 2018 at 1:54 am
    Permalink

    Can I ask for you guys to subscribe to my channel as well? Building a following

    Reply
  • December 26, 2018 at 1:42 pm
    Permalink

    Hello! I am a young Korean who often watches your videos. I'm always watching your videos. I'm writing comments because I'm curious while watching the video. If you look at the table-sourcing drill press, it looks like the birch plywood boards are 18T. I think you use 18T as a whole. You can use 12T in part. Why do you use 18T?

    Reply
  • December 26, 2018 at 1:43 pm
    Permalink

    I don't know if the sentence I left behind is correct. It may not be a question because it was done on the translator,
    Please reply. Merry Christmas. Happy New

    Reply
  • January 6, 2019 at 11:20 pm
    Permalink

    what grade of plywood did you use for the build? The doors look nice. I'm debating if I should do shaker style doors or just flat/slab doors as you did… the best Birch plywood I can get, for a reasonable price, is C2.

    Reply
  • January 11, 2019 at 3:43 pm
    Permalink

    You are The Best in our Blue Planet

    Reply
  • January 13, 2019 at 7:40 pm
    Permalink

    Beautiful – totally awesome!

    Reply
  • January 18, 2019 at 4:12 am
    Permalink

    Maybe look at elevator bolts for adjustable legs. They give you a little wider base.

    Reply
  • January 20, 2019 at 3:52 am
    Permalink

    Nice job fix this build it, U have many tools

    Reply
  • January 27, 2019 at 7:11 pm
    Permalink

    Hi Brad, I enjoyed watching your base cabinets with the doors in the sides and the drawers in the center I have a thought about the t nuts and the carriage bolt that's being used as leveling legs we put the leveling legs directly on concrete over time you could get corrosion and I have a solution for that problem that you might want to try instead of using the round head carriage bolt use a flat head bolt sand off all the information that's printed on the top get a small amount of self-adhesive rubber cut it to size to fit the bolt and then stick it to the bowl now when you put your cabinet up your base unit isn't going to be sitting directly on the concrete to cause gallivanting corrosion.

    Reply
  • January 29, 2019 at 8:57 pm
    Permalink

    Brad, outstanding video and project.  Your attention to detail really resonates with me.  I appreciate quality and your projects always  turn out fantastic!  Thanks for posting!!

    Reply
  • February 19, 2019 at 7:21 pm
    Permalink

    Do you think this method will work for a cabinet that will be 8ft long?

    Reply
  • February 27, 2019 at 7:44 pm
    Permalink

    I love those Kreg jigs and the K5 pocket hole unit. My collection of Kreg jigs is growing rapidly.

    Reply
  • March 3, 2019 at 8:12 pm
    Permalink

    Can these be used for kitchen cabinets?

    Reply
  • March 5, 2019 at 8:23 am
    Permalink

    After watching this video. I think I can build my first cabinet in like 20 minutes.

    Reply
  • March 7, 2019 at 11:07 pm
    Permalink

    Would using 120 degree hinges swing the door enough out of the way to avoid shimming the slides?

    Reply
  • March 16, 2019 at 2:30 pm
    Permalink

    You need to try a keep foreman. I don’t miss my k5 at all. Great video!

    Reply
  • March 16, 2019 at 10:36 pm
    Permalink

    Nice work!

    Reply
  • March 21, 2019 at 7:31 pm
    Permalink

    hey great DIY commerical! thanks a bunch!:)

    Reply
  • March 23, 2019 at 5:44 am
    Permalink

    These are beautiful 💗

    Reply
  • April 3, 2019 at 8:46 am
    Permalink

    could use blum zero protrusion hinge

    Reply
  • April 3, 2019 at 11:50 pm
    Permalink

    Thanks for the tute.

    Reply
  • April 4, 2019 at 8:14 pm
    Permalink

    Brad
    I am working on this design for a pantry. Thanks for the plans it is money well spent.

    Reply
  • April 17, 2019 at 2:20 pm
    Permalink

    Great project. What kind of plywood do you typically use for your shop projects?

    Reply
  • April 19, 2019 at 2:36 am
    Permalink

    Great video with helpful tips!
    Question….any idea why slides need to be recessed 1/8 from front of cabinet. I know instructions show it but I can’t understand why? Seems like flush mount would work just as well and would look better. Any idea why?
    Thanks!

    Reply
  • April 28, 2019 at 1:28 am
    Permalink

    Thanks, this is exactly what I'm looking for. My small workshop is almost done. It's 16X26 with 10ft ceiling. Next step is building all my cabinets and work tables. I can't wait. I have a small 16X16 studio above, with a 10X16 patio. This plan would also work for the small kitchenette upstairs as well. Thanks!

    Reply
  • May 2, 2019 at 8:59 pm
    Permalink

    He makes it look easy

    Reply
  • May 14, 2019 at 7:08 am
    Permalink

    Old video, but I'd suggest using a speed square to ride the jig saw against for those toe kicks.

    Reply
  • May 31, 2019 at 3:16 pm
    Permalink

    This is perfect for my basement liquor cabinet with a couple modifications. Thanks!

    Reply
  • June 10, 2019 at 5:38 pm
    Permalink

    Yet another pocket hole vid where someone goes to the effort to build a cabinet with only screws and no glue.  Its like washing half your car.  It only shows how dirty the other half is.

    Reply
  • June 10, 2019 at 9:06 pm
    Permalink

    💯 Excellent work. I would like to do all that in my cargo trailer

    Reply
  • June 10, 2019 at 9:07 pm
    Permalink

    Where is your shop located?

    Reply
  • June 14, 2019 at 3:13 pm
    Permalink

    I am very impressed with your methodical, logical and certainly repeatable construction of this cabinet and drawers. WOW!!

    Reply
  • July 13, 2019 at 1:38 am
    Permalink

    Awesome build! Sold me, I bought the plans and will build several of these in my garage this year! Thank you for the inspiration

    Reply
  • July 13, 2019 at 6:55 am
    Permalink

    👍👍👍👏

    Reply
  • July 20, 2019 at 11:02 am
    Permalink

    Have you ever met Aston Kutcher?

    Reply
  • July 22, 2019 at 5:33 am
    Permalink

    Top job 😀. Well done. To err is human. Great to see even the best occasionally make a mistake. I have learned more from my mistakes than not. Love the quick tip on fitting the drawer slides. Cheers from Michael. Australia

    Reply
  • July 23, 2019 at 1:03 am
    Permalink

    How can I build this cabinet without all those tools?

    Reply
  • August 7, 2019 at 2:55 pm
    Permalink

    Your videos are great. Please don’t fast forward it.

    Reply
  • August 8, 2019 at 2:43 am
    Permalink

    if that's your garage cabinet I want to see your kitchen

    Reply
  • August 10, 2019 at 10:13 am
    Permalink

    Must be nice to have a full shop to do this in

    Reply
  • August 25, 2019 at 10:02 pm
    Permalink

    Hey Brad, I'm getting ready to start my very first kitchen cabinet build. I've seen Kreg at Workbenchcon but it's nicer to see their products used in your setting. Wish me luck! It's high end cherry so I'm keeping my fingers crossed for few mistakes – haha! Not very likely… thank you, Renee

    Reply
  • August 28, 2019 at 3:14 am
    Permalink

    Super Thanks!! I just completed your base cabinet for my garage and your wall cabinets for my garage. I had never built anything before and I used just the basic hand tools and all the Kreg Tools you used to make it. I am shocked on how great it came out. I studied your cabinet construction and copied it to the letter. I learned so much on this project. Thank You Again!!

    Reply
  • September 9, 2019 at 8:57 pm
    Permalink

    Excelente Trabajo. Todo bien explicado.

    Reply
  • September 16, 2019 at 12:19 pm
    Permalink

    "DIY" – if you have a huge garage full of all the tools and equipment.

    Reply
  • September 27, 2019 at 4:00 am
    Permalink

    I guess pocket holes screws are easier than finger joint or mortise and tenon type joints.

    Reply

Leave a Reply

Your email address will not be published. Required fields are marked *